STARLIGHT / BRACED SUPPORT REVISION V2 — Deco Lantern

TARGET: Bambu Lab X1 Carbon, PLA Matte, 0.4 mm nozzle, 0.20 mm layers.
FIRST PRINT: full-height-stability-test.3mf. It is one actual-height rib
with bracing and two clip-off ties. The short gap coupon already released
successfully, but did not reproduce the wobble of the taller full print.
This braced revision still needs a physical stability/removal test.
If the fin fuses, try coupon-gap-040.3mf. If the rib droops, try gap-020.
Designed clearance for this full kit: 0.30 mm plus a small sampling
allowance (0.025 mm; 0.075 mm beneath Atomic's bead geometry).
Slicer layer placement affects the actual printed separation.

WHY THE PARTS LOOK DIFFERENT
Both bowls are already pole down, open end up. Each fin is beneath the
OUTSIDE of one rib. No central support tree or internal roof scaffold.
The fins now extend higher, have perpendicular stiffening webs, and share
a thin base ring. TWO SMALL TIES ON EVERY FIN intentionally bond to the
rib to resist sideways motion. CLIP BOTH TIES BEFORE PEELING ANY FIN.
These ties change the removal method; do not pull against the ornament.
The polar pad is flat and the upper half uses a 3.2 mm cord hole instead
of integral hanging eyes. The lower bayonet lugs have sloping undersides.
Both halves use matching revised tracks: do not mix with the older print kits.
Tie a stopper knot inside the cord hole, and tie the star threads to that
internal knot/loop. The outer cord loop hangs the ornament from the tree.
Remove the fins before assembling. Keep the existing 20-degree twist joint.

SLICER SETUP
OPEN THE 3MF AS A PROJECT in Bambu Studio, and accept its saved settings.
Importing only the geometry will discard the included printer/process options.
Saved defaults: X1 Carbon / 0.4 nozzle, Bambu PLA Matte, 0.20 mm layers,
3 walls, automatic supports OFF, raft OFF, 3 mm outside brim, Textured PEI.
The saved process is now deliberately slow: outer/inner walls 30/40 mm/s,
wall acceleration 500/700 mm/s2, normal acceleration 1000 mm/s2,
travel 150 mm/s at 1500 mm/s2. Run at Standard (100%) printer speed.
Select your actual build plate and filament/AMS slot before slicing.
The filament profile is Bambu PLA Matte; select the maker's profile if using
another brand. These are saved recommended defaults, not a record of the
unknown exact settings used for the successful coupon print.
Import upper-with-external-fins.3mf and lower-with-external-fins.3mf as
assemblies. Keep every component in its supplied position. Do not arrange
the individual fins, merge them into the bowl, scale or reorient the parts.
Turn automatic supports OFF for this test; the supplied fins are normal
print geometry with a vertical release gap, NOT support-paint modifiers.
Use the SAME filament, layer height and settings for coupon and globe.
Starting point: X1C, PLA Matte, 0.4 mm nozzle, 0.20 mm layers, 3 walls.
The official PLA Matte filament temperatures and machine options are embedded.
Inspect the sliced preview to ensure the 0.8 mm fins survive and the gap
is visible; inspect the bayonet slots and crown. Fins taper near narrow ribs.
Small track roofs and
local bead/lug overhangs rely on bridging. A 3 mm external brim is enabled.
Brim cleanup is outside the bowl. Do not add internal automatic supports.
If the coupon cannot release cleanly, change the gap before printing a bowl.

REMOVAL
1. Let the plate cool and remove the assembly. Trim any outside brim.
2. Locate TWO short vertical tie necks on each fin, where the fin meets
   its rib at about 22–31% and 66% of the bowl body height. They are roughly
   0.5 x 0.8 mm in cross-section and must be clipped with flush cutters.
3. Support the rib gently while clipping. Do not bend the ornament to
   snap the ties. Confirm that ALL twenty ties (at ten ribs) are cut;
   the actual number is two times your selected rib count.
4. Break the reduced sections of the base ring into a few segments.
   Remove the braced fins downward/outward from beneath the convex bowl.
   Their release gap is retained everywhere except the intentional ties.
5. Trim the small remaining tie nubs on the outside of the ribs.
This is an external support frame. Do not try to pull it through the bowl.

FILES
Two prepositioned 3MF bowl assemblies; two bare bowl STLs; three star STLs;
two matching fit ring STLs; stars.3mf and fit-rings.3mf with saved print
settings; three small gap-test coupon 3MFs; model and print settings JSON.
full-height-stability-test.3mf is the first test for THIS revision.
The bare STL files contain no supports and are provided for inspection.
Use the 3MF assemblies for the intended support plan. All units are mm.

Digital checks verify closed meshes, localized tie contact, bed placement,
and removal clearance AFTER clipping. This is not a mechanical simulation.
Print stability, clip force, finish and joint retention remain untested.

This kit matches your selected Studio template and parameter values.
The full-height test uses this template and these dimensions. The small
gap coupons use the original Palm Springs reference rib; print the full-height
test to assess this design. Recheck stability and joint retention physically.
